Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Fontana Homeowners
A gate that won’t open isn’t something you can put off. Whether the motor’s dead, a hinge has torn loose, or the track is binding, every day it sits broken is a day your property isn’t secure and your routine is disrupted. Estate Gate Repair fixes gates in Fontana, and we do it with a level of focus you won’t find from a general handyman. This is all we do. We service nine major automation brands, carry parts for the mechanical side too, and diagnose the actual problem before recommending any repair. Call (866) 893-2220 and describe what’s happening. We’ll tell you what it likely is, what it takes to fix, and when we can get there.
Our team is led by Noel Castañeda, who built this company around one trade: gates. That matters when your Gate Repair in Fontana call is answered by someone who has seen thousands of failures instead of someone fitting you in between garage door calls.
Driveway Gate Repair
Driveway Gate Repair is the service Fontana homeowners call us for most often. Automated driveway gates fail for a handful of predictable reasons: motor burnout from age, control board shorts from Inland Empire heat, gear wear from daily cycles, and sensor misalignment from ground shift. When your driveway gate stops responding, our technician checks the operator, the control board, the safety sensors, and the physical gate itself in one visit. We don’t fix the motor and leave a sagging hinge for next month. Typical driveway gate repair in Fontana runs $150 to $600 depending on whether it’s a mechanical fix or an electrical component replacement; see our Gate Repair pricing for more detail.
Automated Operator Diagnosis
Most driveway gate failures in Fontana start at the operator. We test the motor’s amp draw, check capacitor health, and trace control board function before replacing anything. A burned transformer is a $90 fix. A failed control board replacement runs $250 to $450 with programming.
Safety Sensor Realignment
Fontana soil shifts with wet winters and dry summers, knocking photo eye sensors out of alignment. The gate reverses or refuses to close. Realignment and testing takes under an hour and costs $120 to $180.
Styles & brands we work with
Gate Welding
Gate Welding repairs structural failures that bolt-on fixes can’t address. When a gate post cracks at its base, a hinge tears off the frame, or a decorative iron picket snaps, welding restores the original strength instead of bolting on a patch that fails again. Estate Gate Repair welds on site for most repairs, so your gate doesn’t have to be removed and hauled to a shop. Typical gate welding work in Fontana runs $180 to $500 depending on the extent of the crack and whether post reinforcement is needed. Every weld is ground smooth and primed so the repair doesn’t look like an afterthought.
Hinge and Post Repairs
The most common welding job we do is a hinge that has torn away from the gate frame. We weld the hinge plate back, reinforce the surrounding area with a backing plate when the metal is thin, and reset the gate so it swings true. This usually takes one visit.
Crack and Break Reinforcement
Fontana’s heat cycles stress wrought iron and steel over years, and cracks eventually appear at stress points. We open the crack, weld it solid, and add gusset plates where the design allows. A reinforced gate often ends up stronger than the original build.
Commercial Gate Repair
Commercial Gate Repair covers swing and slide gates at Fontana business parks, self-storage facilities, apartment complexes, and industrial yards. These gates cycle dozens or hundreds of times a day, and the failures compound fast when they’re ignored. A sticking wheel today becomes a burned motor next month. Estate Gate Repair works on commercial operators from DoorKing and LiftMaster, plus the heavy-duty mechanical components that take the daily abuse. Commercial gate repairs in Fontana typically run $250 to $1,200 depending on whether we’re replacing a wheel assembly, rebuilding a track section, or swapping a commercial control board.
High-Cycle Component Service
Commercial operators run far more cycles than residential units, so the wear points are different: drive chains stretch, wheels flatten, and relays arc out. We keep commercial-grade replacement parts on the truck for the most common failures, which means fewer return trips and less downtime for your property.
Access Control Integration
When a gate won’t respond to a keypad, card reader, or telephone entry system, the problem is usually in the control board’s input wiring or the relay logic. We trace the signal from the access device through the operator and fix where the chain breaks rather than replacing everything.
Iron Gate Repair
Iron Gate Repair addresses both structural and cosmetic damage on iron gates throughout properties in Fontana and nearby neighborhoods like Bloomington. Iron is durable, but it rusts, cracks at welds, and sags as hinges wear. We repair broken pickets, re-weld separated joints, straighten bent rails, and treat rust before it spreads. Typical iron gate repair in Fontana runs $150 to $500, with rust remediation and repainting on the higher end. We quote the full scope before starting, so you know whether it’s a quick weld or a multi-stage restoration.
Rust and Corrosion Treatment
Fontana’s dry heat slows rust compared to coastal air, but sprinkler overspray and morning dew still take a toll on iron gates. We grind rust to bare metal, apply rust inhibitor, and prime before painting so the repair lasts instead of bubbling through in a year.
Picket and Rail Straightening
A vehicle bump or wind-loaded slam bends pickets and top rails out of alignment. We straighten what’s salvageable and weld in replacement stock where metal fatigue makes bending risky. The repaired sections get matched to the existing pattern.
Sliding Gate Repair
Sliding Gate Repair gets a gate moving again when it’s off its track, binding on a bad roller, or fighting a misaligned drive chain. Cantilever and V-track sliders solve different problems but fail in predictable ways: bearings seize, wheels flat-spot, chain tension drifts, and debris clogs the track. Estate Gate Repair diagnoses sliding gates by testing the gate’s mechanical movement first, then the motor. We separate a mechanical drag problem from an electrical problem before quoting any work. Sliding gate repairs in Fontana run $180 to $700 depending on whether we’re replacing rollers, rebuilding the track cradle, or servicing the drive system.
Track and Roller Service
Rollers wear into flat spots and the gate starts lurching instead of gliding. We replace bearings and wheels, check the track for sag or debris damage, and adjust the gate so it rolls with even pressure across the full travel. Skipping this step burns out motors prematurely.
Drive Chain and Belt Adjustment
A loose drive chain slaps and jerks; an overtightened one strains the motor and bends shafts. We set tension to manufacturer spec, inspect sprocket wear, and replace stretched chains before they jump a tooth and bind the gate solid.
Wrought Iron Gate Repair
Wrought Iron Gate Repair restores ornamental gates that Fontana homeowners value as much for appearance as function. True wrought iron is increasingly rare, but the term covers the decorative ironwork on most estate gates. These gates collect rust at scroll joints, break at thin decorative elements, and sag when the frame’s integrity fails. We weld cracked scrolls, rebuild broken decorative pieces, reset sagging frames, and match the original finish. Wrought iron repair in Fontana typically runs $200 to $600, with ornate fabrication work priced after we see the gate in person. Your gate keeps its character instead of getting replaced with a mass-produced panel.
Ornamental Detail Restoration
Scrolls, finials, and decorative collars crack when the gate flexes. We weld these back using low-heat methods that don’t distort the surrounding metal, then shape and file the repair to match the original profile. The detail reads as original, not patched.
Frame Sag Correction
A wrought iron gate that drags at the latch side usually has a failing diagonal brace or a stretched hinge. We reinforce the frame with welded gussets at the corners and realign the hinge points so the gate swings square and latches cleanly.
Metal Gate Repair
Metal Gate Repair covers aluminum, steel, and mixed-metal gates across residential properties in Fontana, including newer automated driveway gates in communities around Rialto. Aluminum gates crack at welds; steel gates rust at the bottom rail where moisture collects. Both suffer from hinge and latch failures. Estate Gate Repair fixes the metal and the automation together, because a gate that binds mechanically will kill a new operator just like the old one. Metal gate repairs in Fontana run $150 to $550 depending on the metal type, the repair location, and whether we’re reinforcing or simply re-welding.
Aluminum Frame Cracks
Aluminum is light and rust-free, but it work-hardens and cracks at the welds after years of flexing. We TIG weld the crack with proper filler rod, then add a reinforcement plate behind the repair so the stress that caused the crack gets distributed.
Bottom Rail Rust Repair
Steel gates rust from the inside out at the bottom rail, where water pools against the frame. We cut out the compromised section, weld in fresh steel of matching gauge, and drill drainage holes so moisture doesn’t collect there again.
Wood Gate Repair
Wood Gate Repair rebuilds the structural integrity and function of wooden driveway and garden gates in Fontana. Wood moves with heat and moisture, which loosens joints, warps frames, and rots the bottom of the gate where it meets soil or sprinkler spray. We replace rotted stiles, square and reinforce sagging frames, install new hardware, and get the gate closing smoothly. Wood gate repair in Fontana runs $180 to $500 depending on how much of the frame we replace versus salvage. We work with the wood you have when it makes sense, and we tell you honestly when replacement is cheaper than another round of patching.
Frame and Joint Rebuild
A sagging wood gate usually means the diagonal brace has failed or the half-lap joints have opened. We disassemble the frame, re-cut clean joints, and reassemble with structural screws and waterproof glue. The gate sits square and swings without dragging.
Rot and Hardware Replacement
Bottom rail rot is the leading cause of wood gate failure in Fontana, especially near irrigated lawns. We replace the rotted timber with pressure-treated stock, seal end grain, and install heavy-duty hinges that carry the load across the full frame width.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We work on LiftMaster, DoorKing, Elite, and Mighty Mule operators daily in Fontana. LiftMaster residential boards fail in specific, diagnosable ways, and we keep the common relays and capacitors on hand so the repair doesn’t turn into a week-long parts wait. DoorKing dominates commercial installations, and their board revisions matter when you’re ordering a replacement that actually matches the wiring harness.
Elite and Mighty Mule round out the most common residential operators we see. Elite gates tend to outlast their controller boards, while Mighty Mule failures often trace to actuator issues that are faster to replace than rebuild. The point is this: we diagnose across every brand instead of steering you toward the one we prefer to sell. A brand-agnostic technician finds the actual fault. Whether you have one of these or something less common, we’ll identify it and fix what’s actually broken.
Signs You Need a Pro Right Now
- The gate stops mid-cycle and reverses. This usually means a safety sensor fault or a track obstruction, but it can also signal a failing control board. Either way, the behavior won’t fix itself.
- The motor hums but the gate doesn’t move. A seized gearbox or a broken drive coupling makes that sound. Running it this way burns out the motor fast. Turn it off and call us.
- The gate drags on the ground or scrapes the track. This is a mechanical problem, and forcing the operator to push through it shortens the motor’s life every cycle. Fix the mechanical issue first, then check the motor.
- Your remote works sometimes, and sometimes it doesn’t. Intermittent operation from a remote usually points to a failing receiver or antenna wiring, not a battery issue. It’s a cheap fix now and a lockout later if it fails entirely.
- The gate won’t stay closed or creeps open. A gate that drifts on its own has a failed limit switch or a worn gear brake. That’s a security problem on your property line, not a wait-and-see problem.
Our Process, Step by Step
- 1
Diagnosis first, quote before work. We start by testing the gate’s mechanical movement, then the electrical system, then the operator. The quote reflects the actual failure, not a guess. You approve it before any work starts.
- 2
Mechanical repair and alignment. We fix hinges, rollers, tracks, and alignment issues before touching the electronics. A gate that binds mechanically will destroy new electrical components, so this sequence matters.
- 3
Electrical and operator repair. We replace failed boards, capacitors, limit switches, transformers, or motors, using brand-appropriate parts. Board programming and limit calibration are set to manufacturer spec.
- 4
Safety system testing. We test photo eyes, edge sensors, and auto-reverse function in multiple scenarios. Your gate leaves in a condition that would pass an installation inspection.
- 5
Cycle testing and walkthrough. We run the gate through repeated open, close, and obstruction cycles, then walk you through what failed, what we replaced, and what to watch for. You’ll know exactly what was done.
How Much Does Gate Repair Cost in Fontana?
A typical mechanical gate repair in Fontana runs $150 to $350. A typical electrical repair on an automated operator runs $200 to $700 depending on the component. Board replacements run $250 to $450 including programming; motor replacements run $300 to $700 depending on brand and horsepower. Structural welding work runs $180 to $500. Ornate restoration work on wrought iron gates runs toward the higher end, $200 to $600.
What affects the price: the component that failed, the brand of operator, the gate’s size and weight, and whether access requires lifting the gate off its track or working in a confined column. The fastest way to avoid overpaying is to have the actual failure diagnosed before anyone quotes a repair. That’s built into our process for every job in Fontana. Your estimate is free, and the price you approve is the price on the invoice. You won’t see a higher number after the work is done.
Our Service Area Near Fontana
We cover all of Fontana plus nearby communities including Bloomington, Rialto, Sunnyslope, Glen Avon, Muscoy, Rubidoux, Colton, Highgrove, Grand Terrace, Jurupa Valley, and San Bernardino. Most Fontana calls are scheduled without a service-area trip charge. When you call, we confirm your location and tell you exactly when we’ll arrive. For homeowners searching in the surrounding area, start with our home page to see the full coverage map.
Serving Fontana, CA — Our Local Coverage Area
We’re based in the Fontana area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Fontana
Gate repair is the diagnosis and correction of any failure that prevents a gate from opening, closing, or operating safely; see The Complete Gate Repair Guide for Fontana Homeowners for a deeper look. It covers mechanical issues like broken hinges, bent tracks, and failed rollers, plus electrical issues like dead control boards, burned motors, and misaligned safety sensors. Estate Gate Repair handles both sides of the system in a single visit.
Most gate repairs in Fontana are completed in a single visit, usually one to three hours depending on the failure and part availability. Board swaps, sensor realignments, and roller replacements typically go faster. If a specific board or motor needs to be ordered, we tell you upfront and schedule the return visit.
Gate repair in Fontana runs $150 to $700 for most jobs. Mechanical repairs like hinge replacements and track work average $150 to $350. Electrical repairs on automated operators run $200 to $700 depending on the failed component. You’ll get a firm quote before any work begins. Call (866) 893-2220 for an exact price on your specific issue.
Yes. DoorKing is one of the nine major brands we service, and it’s one of the most common commercial operators in Fontana. We diagnose DoorKing control boards, drive systems, and access-control wiring daily. Parts for common DoorKing failures are usually on the truck the day we arrive.
We make same-day service available for emergency gate failures in Fontana, especially when a gate is stuck open and the property is exposed. Call (866) 893-2220 and tell us what the gate is doing. We’ll tell you the next open window and whether your situation qualifies for immediate dispatch.
We stand behind the parts and workmanship on every repair we do in Fontana. The specific warranty term depends on the component: motors and boards carry the manufacturer’s coverage, while our workmanship has its own guarantee. Details are written on every invoice.
Clear access to the gate and the operator housing is the main thing, so move any vehicles or debris within ten feet of the gate’s swing or slide path. If you have the original remote or keypad codes, keep them handy. If the gate is stuck open, try to secure the property as best you can until we arrive, and turn off the operator if you know where the switch is.
Schedule Your Gate Repair Service in Fontana Today
A broken gate gets fixed on our schedule, not months from now. Call (866) 893-2220 and tell us what’s going on with your gate. We’ll diagnose it over the phone when possible, give you a straightforward price range, and get a technician on the way for a free, no-obligation estimate. Your gate, our specialty.
Written by Noel Castañeda, Owner at Estate Gate Repair, serving Fontana and the surrounding Inland Empire.